BALDOR ELECTRIC COMPANY. P.O. BOX 2400 The above chart provides typical Baldor•Reliance motor dimensions. NEMA QUICK REFERENCE CHART.

Aug 21,  · Therefore, a size 48 frame motor will have a shaft height of 48 ÷ 16 = 3 inches. A 56 sized frame motor would have a shaft height of 3-1/2 inches. Size 56 frame motors are the

Standard IEC Metric Motors ; 7.5, D132S*, D132M, D160M*, D160L ; 11.0, D160M*, D160M*, D160L, D180L.

baldor electric company p.o. box 2400 fort smith, arkansas 72902-2400 u.s.a. nema c-face ba dimensions 143-5tc 2-3/4 182-4tc 3-1/2 213-5tc 4-1/ 4 254-6tc 4-3/4 5000 framede2fhopuvaa ab ba 5 0 7s 1 2-63 4 npt 8 5 0 7l 1 2- /63 8npt 5009s 12-1/2 10 28 15/16 26-27/32 30 2-1/2 6-1/2 4-npt 26-7/8 8-1/2

It is standard to see the “frame” size on every electric motor This is a chart we constructed to reference the different suffixes. Motor 

Aug 25,  · [50] The first two numbers represent the diameter of the motor's housing in millimeters; in this example 50mm [55] The second two numbers represent the length of the motor housing in millimeters; in this example 55mm [3000] The numbers after the dash represent the Kv rating of the motor; in this example 3000 Kv.

Electric motors with improved efficiency, in combination with frequency converters can save frame size 132 and onwards on the NDE side of the motor.

Wire size chart. Selection chart ph induction motor electrical starters eng para engineering tabla tablero seleccionar. Sizing Charts - Student Styles. 10 Pics about Sizing Charts - Student Styles : Wire Size Chart - Inspection Gauges, What Circuit and Wire Size do I need? | King Electric and also Sizing.

You will have the ability to view, print and e-mail drawings, curves and other important information. Please select one of our product group below. Electric Motors Severe Duty and General Purpose: High Efficiency & NEMA Premium Crusher Duty Motors IEEE 841™ Motors Definite Purpose Motors Fractional Motors IEC Tru-Metric Motors AEGIS® Inside

Use this table as a guide only. Horsepower. AC Induction Motors. Single Phase. Three Phase. 115 Volt. 230 Volt. 200 Volt.

ELECTRIC MOTOR SIZING CHART up to 25’ 6 hp 12 hp 20 hp 40 hp 70 hp 100 hp 2.5 kW 5.1 kW 8.5 kW 17 kW 29.75 kW 42.5 kW 70 amps 106 amps 118 amps 167 amps 275 amps 295 amps

CAST IRON 3 PHASE ELECTRIC MOTORS (FRAME SIZES 143TC THRU 405TC) STEEL FRAME ELECTRIC MOTORS SINGLE PHASE AND LOW HP 3 PHASE (FRAME SIZES 56TC THRU 184TC) FRAME SIZE 56TC 143TC 145TC 184TC 1800 RPM 1/2, 10.81 3/4, 11.31 1, 11.81 1 1/2, 12.81 2, 14.25 3, 16.47 5, 17.47 3450 RPM

These are commonly noted as a “T” on the nameplate. For example, if you have a 324T frame motor, every manufacture of motor will have the same shaft diameter, shaft length and bolt hole mounting dimensions, but be warned, your physical size of the motor may differ. There are other common letter suffixes that are also standard.

150% for DC motors) does not correspond to a standard fuse amp rating. LP-CC: 300%(150% for DC motors) or the next larger 240.6 standardfuse amp rating if 300% (150% for DC motors) does not correspond to a standard fuse amp rating. Sizes shown for the LP-CC can also be used for non-time delay fuses such as JKS, KTN-R, KTS-R, JJN, JJS, and KTK-R.

Brook Crompton - Electric Motors. 800 668-6779 - www.brookcromptonna.com Dimensions N Page 71N72 Dimensions Frame Sizes 80 - 315. 71. FOOT MOUNTED.

Motor Power (kW) Motor Current (Amps) Frame Size 0.37 1 71 0.55 1.5 80 0.75 2 80

LEGEND Metric (MM) Dimensions in Black Inch Dimensions in Red d = DCMotors 1 mm = .03937" 1" = 25.40 mm Horizontal Shaft Arrangements Vertical Shaft Arrangements B3 FOOT MOUNTED. B5 "D" TYPE FLANGE AT DRIVE END, NO FEET. B6 FOOT WALL MOUNT WITH FEET ON LEFT HAND SIDE WHEN VIEWED FROM DRIVE END. B7

a QUICK chart for starter sizes is provided here, to the right. HEATER SELECTION Please use the chart as a guide when ordering heaters. If the actual (FLA) Full Load Amperage of the motor is

For the “D” dimension of a three-digit frame number, consider only the first two digits and use the divisor 4. In frame number 145, for example, the first two digits divided by the constant 4 is

kW HP 200; 208 220 230 380 400 415 433; 440 460 500; 525 575 660 1000 0.37 0.5 2 1.8 2 1.03 0.98 ‑ 0.99 1 1 0.8 0.6 0.4 0.55 0.75 3 2.75 2.8 1.6 1.5 ‑ 1.36 1.4 1.21 1.1 0.9 0.6 0.75 1 3.8 3.5 3.6 2 1.9 2 1.68 1.8 1.5 1.4 1.1 0.75

Feet are detachable on all series, from frame sizes 56 to frame size 280. Page 9. Section 1 | Cooling. TEC Electric Motors | www.tecmotors.co