High-Precision Digital Pressure Switch. The settings of the master sensor can be copied to the slave sensors. • Reduced setting efforts • Reduced chance of 

Instruction Manual Digital Pressure Switch Series ZSE40A(F) / ISE40A The intended use of this digital pressure switch is to measure, monitor and display pressure and to provide an output

Digital Pressure Switch Operation Manual ZSE3/ISE3(L) Thank you for purchasing an SMC ZSE3/ISE3(L) Series Digital Pressure Switch. Please read this manual carefully before

pressure Switch output n_2 Hysteresis (H_1) Hysteresis (H_1) Hysteresis (H_1) ON OFF n_1 High pressure Switch If the initial setting is the normally open mode, "P_1" will be displayed. "n_1" will be displayed if it is normally closed mode. The set pressure value can be checked without holding or stopping the switch output operation. Pressure

Contact SMC beforehand and take special consideration of safety measures if the Read and understand this operation manual carefully before assembling, operating or providing maintenance to the product. Input data to the Pressure switch is not deleted, even if the power supply is cut off. (Writing time: 10,000 times, Data duration: 20

See the operating manual for information on how to set and on handling precautions. (Refer to SMC website.) OUT1: Light up when output is turned ON. (Green).

the switch. Reduce the supply pressure to below the max. pressure rating and then reset the switch. Apply atmospheric pressure and then reset the switch. SMC PRESSURE SWITCH RESET SET KPa SMC PRESSURE SWITCH RESET SET KPa SMC PRESSURE SWITCH RESET SET KPa (1) 1 to 5V (±5%F.S.) Load impedance: 1kΩ Max.30V, 80mA Residual voltage: 1V or less Max

SMC instrumentation - ise30/ise30a pressure switch family - ise30 1/8 inch pt version - pressure switch, *lqa. 800.660.0733. View Cart Items 0. Purchase Online • with Net 30 Terms • in 60 minutes Please pull down this page to review full catalog specifications PDF.

Contact SMC beforehand and take special consideration of safety measures if the Read and understand this operation manual carefully before assembling, operating or providing maintenance to the product. Input data to the Pressure switch is not deleted, even if the power supply is cut off. (Writing time: 10,000 times, Data duration: 20

The following instructions must be followed during maintenance: Turn off the power supply Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance Otherwise an injury can result. -5- No.PS※※-OMM0003-I Caution Do not touch the terminals and connectors while the power is on.

The following instructions must be followed during maintenance: •Turn off the power supply •Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance Otherwise an injury can result. Caution Do not touch the terminals and connectors while the power is on.

Digital pressure switch setting . SMC pressure switch.SMC pressure switch model - ISE30A-01-B#smcpressurswitch#digitalswitchE&I technician

smc digital vacuum pressure switch datasheet, cross reference, circuit and application notes in pdf format.

ISE20 is a digital pressure sensor with an informative, easy to read 3 screen, 3 color display. The main screen shows the instantaneous reading in red or green, while two sub-screens can display the setting label and its numeric value in orange. ISE20

Pressure Sensor for General Fluids PSE575. MODEL / Series / Product Number PSE575/576/577. Safety Instructions.

Instruction Manual Digital Pressure Switch Series ZSE40A(F) / ISE40A The intended use of this digital pressure switch is to measure, monitor and display pressure and to provide an output signal. 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Instruction Manual Digital Pressure Switch Series ZSE20B(F)-L/ISE20B-L unsuitable for the standard specif catalogue. 3.1.2 Mounting with bracket (No condensation or freezing)

or more, the switch will be turned OFF . The default setting is to turn ON the pressure switch when the pressure reaches the centre of the atmospheric pressure and upper limit of the rated

catalogue for each series in www.smc.eu. Vacuum pressure. Compound pressure Pressure sensor product variations. Pressure switches. Digital. Switch.

The Pressure switch turns on within a set pressure range (from P1L to P1H) during window comparator mode. Set P1L, the lower limit of the switch operation, and P1H, the upper limit of the switch operation and WH1 (hysteresis) following the instructions given above. (When reversed output is selected, the sub display (left) shows [n1L] and [n1H].)

Input a set value for pressure to perform switch output. Measurement Mode Detects pressure, displays values and performs switching. Other functions such as zero clear can also be set if necessary. Initializing Press the SET button continuously for 2 seconds or longer. The display shown to the right will allow initial setting of the operation mode.